安徽快3

济南震辉保温材料有限公司
地址:章丘工业园
联系人:卢经理
电话:0531-87266820
传真:0531-87266820
邮箱:390062028@qq.com
网址:hbsama.com
当前位置:安徽快3 - 新闻动态
新闻动态
保温层中采用挤塑板的原因和施工要求!
作者:admin 来源:本站 发布时间:2020-09-25 16:01:49 浏览次数:121

  挤塑板是一种利用国外的先进设备所生产的保温材料,它的应用可以让产品有更好的保温隔热作用和防水能力,而且强度也是非常高的,不用担心折弯等情况的发生。现在,很多国家都会把XPS挤塑板应用在建筑工程当中,会将它作为非常好的保温隔热层,避免建筑基层出现冻坏的情形。

  Extruded panel is a kind of thermal insulation material produced by advanced foreign equipment. Its application can make the product have better heat insulation and waterproof capacity, and its strength is also very high, so there is no need to worry about bending. Now, many countries will use XPS extruded panel in construction engineering, it will be used as a very good thermal insulation layer to avoid freezing damage of building base.

                                     15948084503806837.jpg

  现在我国使用挤塑板的地方也是越来越多了,一般是用在一些比较寒冷的区域和水利工程当中。在水泥混凝土当中使用挤塑板保温材料的作用有很多,首先就是可以避免渗漏的情况,避免土壤基层当中的水分过多而引起冻胀的情况。可以让土壤基层当中的温度有效的提升,防止出现结冰的现象,造成土壤的冻胀。还可以避免混凝土当中出现过多的冰层压力和冻胀压力的情况,使混凝土的冻胀问题得到有效的控制。

  Now our country uses more and more extruded board, which is generally used in some cold regions and water conservancy projects. In cement concrete, the use of extruded board insulation material has a lot of functions. First of all, it can avoid leakage and avoid frost heaving caused by excessive moisture in the soil base. It can effectively improve the temperature in the soil base, prevent the phenomenon of freezing and cause soil frost heaving. It can also avoid excessive ice pressure and frost heaving pressure in concrete, and effectively control the frost heaving problem of concrete.

  在对挤塑板进行施工的时候,还需要达到一定的条件,基层墙体的质量必须要进行验收,达到要求了以后才可以对外墙进行外保温施工。在施工的时候,墙体上面的各种杂志一定要先进行清理,墙面不是非常平整的时候,要对其进行修补才可以。要将各种设备等部件安装在墙面外面的时候,需要先留好对挤塑板的施工。要让门窗的洞口通过相关的验收工作,同时满足质量的而需求,而且建筑物基层在受到正负风压的时候,它层间移动的位置不能太大。

  In the construction of extruded board, it is also necessary to meet certain conditions. The quality of the base wall must be checked and accepted, and the external insulation construction of the external wall can only be carried out after the requirements are met. During the construction, all kinds of magazines on the wall must be cleaned first. When the wall is not very flat, it can be repaired. To install all kinds of equipment and other components outside the wall, it is necessary to reserve the construction of Extrusion board. To make the door and window openings through the relevant acceptance work, while meeting the quality requirements, and the building base in the positive and negative wind pressure, its interlayer movement position should not be too large.